Won't These Melt?!? 15amp Receptacles on 20 amp Circuits!!!

Video Description

In the latest episode of Electrician U, Dustin digs into some of the reasons WHY we are allowed to install 15a devices on 20a rated circuits in certain instances and what can happen if we overload those circuits. 🤘⚡️EU Learning System⚡️🤘 For Individuals --- https://electricianu.com/learning-system-for-individuals/ For Businesses --- https://electricianu.com/learning-system-for-businesses/ -Video courses on every side of the electrical trade (theory, code, safety, wiring, install, troubleshooting, leadership, and more) -Practice exams for 2017, 2020, 2023 code -YouTube videos categorized and searchable -Audio lessons -Forum -Business version has admin portal and ability to assign learning to technicians and monitor progress -Any business size from 2 techs to 2,000! 🎓💡CONTINUING EDUCATION💡🎓 Sign up here --- https://electricianu.com/continuing-education/ -State Approved -Video Based ✍📝PRACTICE EXAMS📝✍ Get them here --- https://www.electricianu.com/electrician-u-membership/ -2017, 2020, and 2023 NEC versions -Online Residential Wireman Exam -Online Journeyman Exam -Online Master Exam -300 Question Online Code Cannon (not license specific, all code) -Take as many times as you want -All of the above come with printable PDFs 🎤🎧PODCAST🎧🎤 Spotify: https://open.spotify.com/show/7ldCwdxhWnT0R3nne96XjC?si=a42a98b83c3549fc&nd=1 Apple Podcast: https://podcasts.apple.com/us/podcast/electrician-u/id1583270265 📱👍SOCIALS👍📱 TikTok - https://www.tiktok.com/@electricianu Instagram - https://www.instagram.com/electrician_u/ Facebook - https://www.facebook.com/TheElectricianU/ Reddit - https://www.reddit.com/r/ElectricianU/ Rumble - https://rumble.com/c/ElectricianU Discord - https://www.discord.gg/electricianu 🎧🎹Music, Editing, and Videography by Drake Descant and Rob LeBlanc🎹🎧 #electrician #electrical #electricity We usually see the results of breakers not tripping as they should, but the devices melting instead around the winter months where portable space heaters are more plentiful, or circuits are overloaded with Christmas lighting. Part of the problem with this is due in part to being able to install a 15a receptacle, but that 15a breaker can EASILY be replaced with a 20a breaker by anyone, thus negating the wiring and associated device being able to sustain the increased amperage and failing. In fact, article 210.21 (B) of the NEC states that SINGLE receptacles installed on an individual branch circuit shall have an ampere rating of not less than that of the branch circuit. BUT 201.21(B)(3) and table 210.21(B)(3) allows us to install 15 OR 20 amp rated receptacles on a 20a branch circuit. Why would this be? Well, if you were to relate it to a service size, not EVERYTHING will be used at its capacity at the same time, and we are allowed to install one under this assumption. If you added up ALL the 20a breakers in your panel, along with the larger ones for your AC, water heater, etc., it would probably end up well over 200a on a standard 200a service in most residences. Another way to look at it would be that while you may be utilizing the entire 20a worth of current on the ENTIRE circuit, the chances are very slim that you would be pulling 20a worth at any one device. 210.21(B)(2) further states that a receptacle connected to a branch circuit supplying 2 or more receptacles, that receptacle shall not supply a total cord-and-plug connected load in excess of the maximum specified in Table 210.21(B)(2). This table, for instance, shows us that for a 15 or 20a circuit, with a 15a receptacle, that we can have a maximum load on that cord-and plug connected circuit of 12a. If that were to be adhered to, there would be no problem. But are we, the installing electrician, available to guide the homeowner as to what they should plug into their house circuity or are most homeowners savvy to our electrical code? But wouldn’t the 20a breaker just trip if you had more than 20a worth of current being drawn on it? Not necessarily. If you dumped more than 20a all at once, then yes, it should trip. But thermally, if you allowed that amperage and heat to build up slowly then the breaker is designed to trip at about 130% of the value it is rated for. In the case of a 20a breaker, that would be 24a! And someone was to plug those space heaters into a single 15a rated receptacle, then that receptacle COULD melt before the breaker tripped! 210.23(A)(1) & (A)(2) also mention how much you can plug into a branch circuit, (A)(1) telling us that the rating of any one cord-and-plug connected equipment not fastened in place shall not exceed 80% of the branch circuit ampere rating, and (A)(2) telling us that utilization equipment fastened in place shall not exceed 50% of the branch circuit ampere rating where lighting, and/or other cord-and plug connected equipment are also supplied.